ADT7485A
http://onsemi.com
8
Table 7. 16-BYTE DIB DETAILS
Byte
Name
Value
Description
0
Device
Capabilities
0xc0
Fixed Address
Device
1
Version/Revision
0x10
Meets Version 1 of
SST Specification
2, 3
Vendor ID
00x11d4
Contains Company
ID Number in Little
Endian Format
4, 5
Device ID
0x7485
Contains Device ID
Number in Little
Endian Format
6
Device Interface
0x01
SST Device
7
Function
Interface
0x00
Reserved
8
Reserved
0x00
Reserved
9
Reserved
0x00
Reserved
10
Reserved
0x00
Reserved
11
Reserved
0x00
Reserved
12
Reserved
0x00
Reserved
13
Reserved
0x00
Reserved
14
Revision ID
0x05
Contains Revision ID
15
Client Device
Address
0x48 to
0x4a
Dependent on the
State of Address
Pin
Ping()
The Ping() command verifies if a device is responding at
a particular address. The ADT7485A shows a valid non-zero
FCS in response to the Ping() command when correctly
addressed.
Table 8. PING() COMMAND
Target Address
Write Length
Read Length
FCS
(Not Necessary)
0x00
0x00
ResetDevice()
This command resets the register map and conversion
controller. The reset command can be global or directed at
the client address of the ADT7485A.
Table 9. RESETDEVICE() COMMAND
Target Address
Write
Length
Read
Length
Reset
Command
FCS
Device Address
0x01
0x00
0xf6
GetIntTemp()
The ADT7485A shows the local temperature of the device
in response to the GetIntTemp() command. The data has a
little endian, 16-bit, twos complement format.
GetExtTemp()
Prompted by the GetExtTemp() command, the ADT7485A
shows the temperature of the remote diode in little endian,
16-bit, twos complement format. The ADT7485A shows
0x8000 in response to this command if the external diode is
an open or short circuit.
GetAllTemps()
The ADT7485A shows the local and remote temperatures
in a 4-byte block of data (internal temperature first, followed
by external temperature) in response to a GetAllTemps()
command.
SetExtOffset()
This command sets the offset that the ADT7485A will use
to correct errors in the external diode. The offset is set in little
endian, 16-bit, twos complement format. The maximum
offset is ?28癈 with +0.25癈 resolution.
GetExtOffset()
This command causes the ADT7485A to show the offset
that it is using to correct errors in the external diode. The
offset value is returned in little endian format, that is, LSB
before MSB.
ADT7485A Response to Unsupported Commands
A full list of command codes supported by the
ADT7485A is given in Table 6. The offset registers
(Command Code 0xe0) are the only registers that the user
can write to. The other defined registers are read only.
Writing to Register Addresses 0x02, 0x09, and 0x15 to 0xdf
shows a valid FSC, but no action is taken by the ADT7485A.
The ADT7485A shows an invalid FSC if the user attempts
to write to the device between Command Codes 0xe2 to
0xee. These registers are reserved for the manufacturers use
only, and no data can be written to the device via these
addresses.
Voltage Measurement
The ADT7485A has four external voltage measurement
channels. It can also measure its own supply voltage, V
CC
.
Pins 5 and 8 measure the supplies of the 12 V, 5.0 V,
processor core voltage (V
CCP
), and 2.5 V pins, respectively.
The V
CC
supply voltage measurement is carried out through
the V
CC
pin (Pin 1). The 2.5 V pin can be used to monitor a
chip-set supply voltage in a computer system.
Analog-to-Digital Converter
All analog inputs are multiplexed into the on-chip,
successive approximation, analog-to-digital converter
(ADC). This has a resolution of 10 bits. The basic input
range is 0 V to 2.25 V, but the inputs have built-in
attenuators to allow measurement of 2.5 V, 3.3 V, 5.0 V,
12 V, and the processor core voltage (V
CCP
) without any
external components.
To allow for the tolerance of these supply voltages, the
ADC produces a specific output for each nominal input
voltage and therefore has adequate headroom to cope with
overvoltage. The full-scale voltage that can be recorded for
each channel is shown in Table 10.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ADT7486AARMZ-RL
IC TEMP SENS DGTL 2CH SST 10MSOP
ADT7488AARMZ-RL
IC TEMP/VOLT DGTL W/SST 10MSOP
ADT7518ARQZ
IC SENSOR TEMP QD ADC/DAC 16QSOP
AT30TS00-MAH-T
SENSOR DGTL TEMP I2C/SMBUS 8WDFN
AT30TSE002B-MAH-T
SENSOR DGTL TEMP I2C/SMBUS 8WDFN
BD3504FVM-TR
IC REG CTRLR SGL POS ADJ 8MSOP
BD3521FVM-TR
IC REG CTRLR SGL 1.5V MSOP8
BD9153MUV-E2
IC REG TRPL BCK/LINEAR 24VQFN
相关代理商/技术参数
ADT7485AARMZ-R7
功能描述:板上安装温度传感器 TMP SNSR/VLTG MON W/SST INTERFACE RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
ADT7485AARMZ-REEL
功能描述:IC TEMP/VOLT DIG SENSOR 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6
ADT7485AARMZ-REEL7
功能描述:IC TEMP/VOLT DGL SENS SST 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6
ADT7486A
制造商:AD 制造商全称:Analog Devices 功能描述:Digital Temperature Sensor with SST Interface
ADT7486AARMZ-R7
功能描述:板上安装温度传感器 DGL TMP SNSR SST INF RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
ADT7486AARMZ-REEL
制造商:AD 制造商全称:Analog Devices 功能描述:Digital Temperature Sensor with SST Interface
ADT7486AARMZ-REEL7
功能描述:IC TEMP SENS DGTL 2CH SST 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6
ADT7486AARMZ-RL
功能描述:板上安装温度传感器 DGL TMP SNSR SST INF RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor